1980 Honda Xr250 Motorcycles for sale

1-4 of 4

Sort By

Honda : XR 1980 honda xr 250

Honda : XR 1980 honda xr 250

$1,400

Duluth, Georgia

Year 1980

Make Honda

Model XR

Category Off Road Motorcycles

Engine 250

Posted Over 1 Month

great condition for it's age - runs and shifts smoothly replaced Rear shocks- Progressive Suspension replaced timing Chain honed cylinder and replaced piston and rings. Didn't need it but did it while I was in there. replaced clutch and clutch springs replaced Chain and sprockets, Front is steel -1, Rear is stock steel, o-ring chain. Still in good shape! always covered in WD-40 after washing always used a synthetic blend engine oil stored in an air conditioned basement for the last two years foam air filter missing (metal cage exists) - speedometer cable missing - tool pouch missing - dent in gas tank can be tagged in Georgia with bill of sale.

Trim XR250

1980 Honda Xr 250R

1980 Honda Xr 250R

$1,500

Duluth, Georgia

Year 1980

Make Honda

Model Xr 250R

Category Dual Sport

Engine 250 cc

Posted Over 1 Month

1980 Honda Xr 250R, thinning the herd, only 3 more to go one XR500 1979, one 1996 XR250, bored, ported, hot cam and this XR250 1980 model she's running fine + everything works, aftermarket shocks, aftermarket muffler, previous owner swears the mileagee is correct not in perfect condition, a small dent in the tank, tool pouch missing, rip in the seat no title, in GA vehicles model year 85 and older can be tagged with just a VIN verification and a bill of sale but even when tagged do not get issued a title bike is located just N-E of metro Atlanta $1,500.00

1996 Honda Xr 250R

1996 Honda Xr 250R

$1,400

Duluth, Georgia

Year 1996

Make Honda

Model Xr 250R

Category Dirt Bikes

Engine 250 cc

Posted Over 1 Month

1996 Honda Xr 250R, thinning the herd, only 3 more to go one XR500 1979, one XR250 1980 and this 1996 XR250R, bored, ported, hot cam definitely was used, has the scuffs and scrapes to proove it but it is a one-kick starter and everything works no title bike is located just N-E of metro Atlanta $1,400.00

Honda : XR XL350 Powroll 403cc Megacycle Cam Al Baker's Pipe XL500 Mugen WORKS Shocks VMX

Honda : XR XL350 Powroll 403cc Megacycle Cam Al Baker's Pipe XL500 Mugen WORKS Shocks VMX

$1,995

Salem, Oregon

Year 1977

Make Honda

Model XR

Category Off Road Motorcycles

Engine 350

Posted Over 1 Month

FOR SALE 1977 HONDA XL350 We bought this bike a few years ago from a long time friend. This friend had owned this bike since 1985. Way back in 1985 he set off on a journey to create his own version of Bill Bell's Baja Bullet from the late 1970's. Clean and clear Oregon title. First off was the installation of a 403cc Powroll big bore kit. Also installed at that time was a mild Megacycle cam. While disassembled a brief clean up and smoothing out of the cylinder ports was done. Next was the fitting of a 1980 Honda XR500 carburetor. Well known for running great and good gas mileage. While the bike was apart the frame was cleaned up and any unneeded mounting hardware or tabbing for the OEM air filter box and battery stuff was neatly removed. Frame was professionally painted as Bob was pro-painter and owned his own auto body shop. At this time a custom "Mugen-like" air box was handmade and neatly installed/mounted on this bike. Bob is also a great fabricator. A new Al Baker's XR's Only exhaust pipe was purchased and installed. Still looks good. Sounds great! Header pipe has minor surface rust. While the rear end was apart the frame rails were custom modified for the installation of a at-the-time "modern" 1982 CR480 seat and rear fender section. Eliminating the big heavy XL350 seat and seat lock/helmet holder parts. All street-legal parts including: lights, wireharness, switches ETC were removed and are not included in the purchase of this bike. This bike could be made street legal again with time and effort finding the parts. We'd leave it just like it is though. A de-tabbed Honda XR500 rear swingarmwas mated up to the frame at this time as well. New mounts were made for the install of an UNKNOWN brand chain slider and chain guide. Both slider and guide are intact and in good used shape 1981-ish Honda XR500 front forks and clamps were installed. Increasing suspension travel and dampening. Custom steering stops were added to frame to make the new forks clear the then-new Clarke plastic tank. The Clarke tank now is a bit faded with some discoloration. Some of this fade disappears when you spray shiny stuff on it. We sprayed shiny stuff on it for the pics. You can see some of the stain on the sides though. Petcock currently functions fine. The vent tube nipple on the Clarke cap is broken. New caps are still avail from Clarke. In 1985, new Works Performance shocks were installed at that time too. Shocks are not leaking currently in 2016. Both seem to rebound and dampen nicely. Bike starts are runs well. Makes excellent power. Ideal for Vintage MX, trail riding or perhaps even flat tracking. Instant 2-3 gear wheelies on command. No clutch slipping needed. Brakes work decently well. Could probably use a good cleaning of the drums and shoes. Both still work OK and do not drag or stick when used. Shorty front brake lever decreased leverage and makes the cable pull harder than OEM. Front/rear tires are in good used shape. Mileage unknown. Front and rear rims are clean without dents or damage. Each wheel has 3-4 corroded spokes. Could be cleaned up and detailed with little effort. Front CR480 fender is faded but is not cracked. Rear CR480 fender is in good clean shape. Seat does not have any rips or tears. Foam feels nice and comfy. The aluminum Inter-Am handlebars are in good shape. After market controls work decently well also. The shorty clutch lever makes the clutch pull seem a bit firm. Throttle operates decently. The upper end of the throttle cable housing is separated from the end cap on the housing. Still works OK. Has a SUPER COOL solid aluminum exhaust valve cover with manual decompressor device built it. Cable is hooked up to a lever on the handlebar. All these parts work nicely. This bike was casually trail ridden in the Oregon coastal mountains for several years before being parked. Exact mileage on engine and performance parts is UNKNOWN. Mileage on the speedometer reads 9369. Bob said these meter was purchased at a local salvage yard though. Right before we purchased it Bob removed the top end to inspect for wear. All looked great and was reassembled with new gaskets. Bike starts and runs cleanly. No smoke. No unusual knocks, ticks or smoke, Transmission shifts smoothly. All kickstart parts operate properly too. This is an old bike with a lot of cool parts on it. Lots of time and effort was spent on this bike way back in 1985 to make it what it is. Bob is very meticulous. He was a auto-body paint shop owner and was also known to build custom tube-frames for sand rails. With a couple new fenders, number plates and perhaps that Bill Bell MR250 gas tank you would have quite the vintage racer!!!! Or simply ride and enjoy as-is. This bike does not have any remaining warranty. Sold as-is. With any 39 year old bike you will need to clean/replace/adjust/tune to your specific needs. If you have specific questions please ask them via the ebay message system. Yes we do ship anywhere in the USA 48 states !!!!We are Bill's Motorcycles Plus in Salem Oregon. Award winning, long time "real-deal" Gas-Gas and Husqvarna motorcycle dealer and riders. Oregon Dealer # DM0280.If you have questions please call toll free 1-888-806-1153 and ask for Bill Shipping and crating is available within the USA 48 states. Shipping to your local business with a fork lift or local shipping terminal approx. cost is $250-450 depending on your location and distance from us. Call or ask for shipping quotes, please include your zip code.Please no bidders below +5 current feedbacks. Any new members or zero feedbackers must please call us first to communicate interest and intent to complete payment in case they should win the auction. Zero feedbackers who do not do so will be blocked. On Jan-22-16 at 13:42:14 PST, seller added the following information: CLEAN AND CLEAR OREGON TITLE.

Trim XL350 Baja Bullet